Bill of Materials for Cyclic Simulator

A1	Design -	AIRBORN		No part		NS
BOX1	H0376	RQD PART		TPI1-S6X		NS		Gainta:G1814	130 x 75 x 28 snap together ABS case
C1	220nf	RAD5		CAP5-224	445-4803-ND	th		TDK:FK28Y5V1H224Z	DC supply input bypass
C2 C5 C6 C7 C8	1uf	RAD5	5 ea	CAP5-105	445-2865-ND	th		TDK:FK24Y5V1H105Z	Monolithic ceramic
C3 C4	47uf	RPOL2/5	2 ea	EL20-476	P5550-ND	th		Pana:ECA-1VHG470	Main timing capacitors; Lie part flat on PCB
CN1 CN2	Accelorom	TBLK3.8/4H	2 ea	GQB9-D4H +MATE	277-1208-ND	th		Dinkle:ECH381R-04P	In and Out connectors (& power)
D1	1N4746	DIODE10		ZD1W-18V	MOU:512-1N4746A	th		Fairchild:1N4746A	Overvoltage protection diode
IC1	4093	DIP14		JQL3-3PT	296-2068-5-ND	th		TI:CD4093BE	Quad 2 input NAND Schmitt: Switch triggered RS F/F
IC2	LM358	DIP8		L16F-QGJ	296-1395-5-ND	th		TI:LM358P	Output buffer/amplifier
IC3	LM339	DIP14		SM6Y-VUA	296-6605-5-ND	th		Quad voltage comparator	Cycle start and run detection comparator
IC4	LM317LZ	TO-92A		CZZ1-JZF	LM317LZ-ND	th		Fairchild:LM317LZ	10V supply; Lie part flat on PCB
IC5	78L05	TO-92A		X23W-3TO	LM78L05ACZFS-ND	th		ST:L78L05ACZ	4.5V reference supply; Lie part flat on PCB
P1 P2 P3 P4	1M	VR9MMVER	4 ea	EX21-DZT	CT2271-ND	th		CTS:296UD105B1N	9mm spline shaft single pot; vert; Mount on Solder side of PCB
PCBLAM#1	AB1003279	PCLAMINATE		Gerbers		NS		Order PCBs from AirBorn
R1	3k3 1%	AXIAL10		MF25-332	MOU:660-MF1/4DC3301F	th		Koa:MF1/4DC3301F	Vout = ((R1/R2)+1) * 1.25
R2	470R 1%	AXIAL10		MF25-471	MOU:660-MF1/4DC4700F	th		Koa:MF1/4DC4700F
R3	15R NFR	AXIAL10		NF25-150	PPC15ATR-ND	th		Vishay:NFR2500001509JR500	Overvoltage protection resistor - may open on surge
R4 R5	680R	AXIAL10	2 ea	CR25-681	680QBK-ND	th		Yageo:CFR-25JB-680R	R4 & R5 set switch LED brightness
R6 R7 R8 R9 R10 R11 R12 R13	10k	AXIAL10	8 ea	CR25-103	10KQBK-ND	th		Yageo:CFR-25JB-10K
R14 R16	8k2	AXIAL10	2 ea	MF25-822	MOU:660-MF1/4DC8201F	th		Koa:MF1/4DC8201F	(May Substitute 8.25k 1% stock parts)
R15	100k	AXIAL10		CR25-104	100KQBK-ND	th		Yageo:CFR-25JB-100K
S1	IncliStart	TACT6_LED		JOWB-MOB		th			Lit pushbutton
S2	AccelStart	TACT6_LED		JOWB-MOR		th			Lit pushbutton
S3	ON/BYPASS	SLIDE4/EDG		B4MT-S7Q	MOU:10SL001	sm		MountainSwitch:10SL001	Slide switch used to bypass unit operation if rqd
T1	GND	TP		No part		TP			Ground testpoint
T2	+12	TP		No part		TP			+12V testpoint
T3	10V	TP		No part		TP			+10V testpoint
T4	4.5V	TP		No part		TP			+4.5V testpoint
T5	Inc4.5	TP		No part		TP			Incl 0 to 4.5V signal
T6	IncOut	TP		No part		TP			Inclination out
T7	Acc4.5	TP		No part		TP			Accel 0 to 4.5V signal
T8	AccOut	TP		No Part		TP			Acceleration out

PART NUMBER SUFFIXES:
-CUS	Customer supplied
-OMIT	Part is LEFT OFF PCB!
-OPT	Part MAY be left off PCB!
-SKT	Part needs socket!
-PGM	Needs programming!
-PB	Part is NOT ROHS
-?/-ERR	PN is Not correct
-NOTE	Find & Read Part note!

Version Date: 15 Mar 2010
PCB number: AB1003279
PCB size: 63.5mm x 124.5mm, 2.500in x 4.900in, HxW = 7903sq mm, 12.25sq in

Distributor part numbers are quoted for contingency and comparison and do not constitute a recommendation or requirement: Purchase of an identical, same manufacturer part from a more cost effective distributor is encouraged. Substitution of parts from a different manufacturer requires engineering approval. In addition, substitution of a different part from the same manufacturer requires engineering approval.

Part numbers may be subject to change. Distributors part numbers are sometimes for economical buy quantities such as 1000pcs. It is the readers responsibility to check pack buy quantities, and minimum order quantities.

Mounting types:
[sm] Part is surface mount
[th] Part is thru-hole
[TP] Part is a test point
[NS] Part is not soldered

Part numbers were originally entered by hand. Verify parts before ordering.